Real-time FFT, right in your browser

Spectrum Analyzer

Free online audio spectrum analyzer, live from your mic Live

Point your microphone at any sound and watch its frequencies move in real time. Find the loudest note, spot mains hum, check a speaker. No sign-up, nothing to install.

  • 20 Hz – 20 kHz
  • FFT up to 32,768
  • Mic, file or tab audio
  • Phone · tablet · PC

Press Listen to see your sound live

The browser asks to use your microphone. Your sound stays on this device.

Or drop an audio file here.

Peak—
Note—
Level—

Peaks
  1. No sound yet.
Response
Detail
Which window?
Display
Frequency scale

Zoom: pinch the graph, or hold Ctrl and scroll.

Processing
Weighting
Guides and markers

Markers: click the graph, or long-press on a touch screen (up to 4). Press M to put one at the mouse.

Source

Files are read on this device only; they are never uploaded.

Speaker test sound

Turn your volume down first. Pink noise is loud; it fades in over 3 seconds.

Press Listen too, so the mic hears the speaker. 1/6-octave smoothing (Speaker preset) makes the curve easy to read.

Reference traces

Save trace keeps the current curve as a faint line (up to 3), so you can compare live sound with it.

    Export and share

    The link keeps your settings, never your sound.

    Recent results
      Sound never leaves your device. Nothing is recorded or uploaded. Space listenF freezeS snapshot1–4 viewsM markerDouble-click: reset zoom

      How to use the spectrum analyzer

      1. Press Listen

        Press Listen and allow the microphone when the browser asks. The graph starts moving at once: low sounds on the left, high sounds on the right, loud sounds reach higher. No mic at hand? Choose Demo sound or Audio file as the source.

      2. Pick a preset

        A preset sets the range, the detail and the smoothing for one job. Music shows note names, Voice marks harmonics and the vowel zones, Speaker smooths the curve so you can judge a speaker, and Mains hum zooms in on 20 Hz – 1 kHz and looks for hum. Change anything and your own mix is kept as Custom.

      3. Read the peak

        Under the graph you see the loudest frequency in hertz, the nearest musical note with how far off it is in cents, and the level in dBFS. The three needle meters show the same values at a glance. Press Freeze (or double-tap the graph) to hold a moment, then save it as a picture or a CSV file.

      38 free tools for sound, rooms and radio

      This analyzer is the start. Each group below has its own tools, from a scrolling spectrogram to RF calculators. Every tool opens right here in your browser; any marked Soon is on the way.

      What you can do with it

      Check an instrument's tone

      Play one note and read it off. The tallest peak is the note you played; the smaller peaks above it are its harmonics, and their pattern is what makes a guitar sound different from a flute. The cents reading tells you how far the note is from true pitch.

      Check your speakers

      Play pink noise through the speaker and hold the mic at your listening spot. A good speaker gives a fairly smooth, gently falling curve. A big bump points to boomy bass or a room resonance; a deep dip often means the speaker or the room cancels that range.

      Find mains hum

      A low buzz from an amplifier, a mixer or a guitar rig is often mains hum. The Mains hum preset looks for 50 Hz or 60 Hz and their harmonics and tells you which one it found and how loud it is. Then read how to fix mains hum.

      Analyze a recording

      Open an mp3, wav, flac or m4a file and watch its spectrum while it plays. The file is read on your device and never uploaded. To analyze a whole audio file at once, use the file tool.

      Measure a room

      Play pink noise and switch to the RTA view. Bars that stick up show where the room adds energy, often in the bass. For finer work, use the full 1/3-octave RTA with a measurement mic.

      See your voice

      Talk or sing and watch the harmonics line up. The Voice preset shades the zones where vowel formants sit, so you can see why "ee" and "oo" look different. The scrolling spectrogram shows your voice over time.

      How to read the graph

      Peak: 220 Hz, note A3 Harmonics: 2×, 3×, 4×, 5× Noise floor 0−20−40−60−80201001k10kFrequency (Hz, log scale)dBFS
      One note on a spectrum: the fundamental, its harmonics and the noise floor under them.

      The frequency axis: Hz, log vs linear

      Left to right is pitch, in hertz (Hz): how many times a second the air moves. Bass sits from about 20 to 250 Hz, voices mostly from 100 Hz to 4 kHz, and the "air" of cymbals up to 20 kHz. The log scale gives every octave the same width, which matches how we hear. Switch to linear to see evenly spaced harmonics, as in the hum preset.

      The level axis: dB and dBFS

      Up and down is level, in decibels. This tool uses dBFS: 0 dBFS is the loudest level your device can record, so every real reading is below zero. Each 6 dB is about double or half the signal; 20 dB lower is a tenth. A calibrated mic and the calibration knob let you match a known sound level.

      Peaks, harmonics and the noise floor

      A peak is a strong single frequency. Most sounds have a fundamental (the note you hear) and harmonics at 2×, 3×, 4× of it. The low, uneven line under everything is the noise floor: room noise and mic hiss. For a full walk-through, see how to read a spectrum analyzer.

      What is a spectrum analyzer?

      A spectrum analyzer shows how strong each frequency in a signal is. It splits a sound into its parts, like a prism splits light into colours.

      There are two big families. Audio analyzers work from about 20 Hz to 20 kHz, the range people hear, and they are used for music, speech, speakers and rooms. RF analyzers look at radio signals in the megahertz and gigahertz range: WiFi, mobile phones, radios and the noise from electronics.

      Old bench analyzers sweep: they tune a narrow filter across the range, one frequency after another. Modern tools, this one included, use the FFT (fast Fourier transform): they take a short slice of the signal and work out all frequencies at once, many times a second. A larger FFT size gives finer detail but reacts more slowly. Learn more about what a spectrum analyzer is.

      Spectrum analyzer vs oscilloscope

      An oscilloscope draws the signal over time: you see the shape of each wave, its timing and its peaks. A spectrum analyzer draws the same signal over frequency: you see which tones are in it and how strong each one is. Use a scope to see clipping, timing and wave shape; use a spectrum analyzer to find hum, harmonics and tone balance. This page has both: the Scope view shows the wave, and the online oscilloscope has every scope feature. More in spectrum analyzer vs oscilloscope.

      Do you need a hardware spectrum analyzer?

      For sound, usually not. Your phone or laptop mic is enough to find a note, spot hum or compare two settings. Its limits are honest ones: most phone mics fall off below about 50 Hz and above about 16 kHz, and they are not calibrated, so levels are relative.

      For exact speaker and room measurements, a USB measurement mic with its own calibration file, such as the miniDSP UMIK-1, gives a flat, known response. For radio signals you need different hardware, because a mic cannot hear radio at all. A USB receiver like the RTL-SDR Blog V4 shows live radio spectrum on a computer for little money, and a handheld analyzer works on its own.

      tinySA Ultra

      A pocket-sized RF spectrum analyzer with a touch screen and a battery, made for radio signals in the MHz and GHz range. A good first tool for checking transmitters, antennas and interference.

      Check price on Amazon

      We may earn a commission if you buy through these links. It does not change the price.

      Compare the options in our guide to the best hardware spectrum analyzers.

      Your sound never leaves your device

      Everything on this page runs in your browser. The microphone, the files you open and the tab audio you share are analysed on your own phone or computer; nothing is recorded or sent to a server. There is no sign-up, and after the first visit the analyzer even works offline.

      FAQ

      Is this spectrum analyzer free?

      Yes. Every tool on the site is free, with no sign-up and no limits. Ads pay for the site.

      Does my sound get uploaded?

      No. The analysis runs in your browser on your device. Nothing you play or record is sent to any server.

      Can my phone work as a spectrum analyzer?

      Yes. Open this page in Chrome or Safari, tap Listen and allow the microphone. Add it to your home screen to use it like an app, even offline.

      How accurate is it?

      Frequencies are accurate to a fraction of a hertz with a large FFT size. Levels depend on your mic: phone mics are weak below about 50 Hz and above about 16 kHz, so use a measurement mic for exact levels.

      What FFT size should I use?

      4,096 or 8,192 for music and voice. Use 32,768 to split close low frequencies such as 50 vs 60 Hz hum. Bigger sizes show more detail but react more slowly.

      Why does the graph move when it is quiet?

      The mic always hears some room noise and its own hiss. That low, wobbly line is the noise floor. Real sounds stand well above it as peaks.

      Can it analyze an audio file?

      Yes. Choose “Audio file” as the source and pick an mp3, wav, flac or m4a. For a whole-file report use the Audio File Spectrum Analyzer.

      What is the difference between dB and dBFS?

      dBFS counts down from the loudest level the device can record (0 dBFS). It is not sound pressure (dB SPL) unless you calibrate your mic.

      Written and tested by the SpectrumAnalyzer.app team · Last checked

      How we tested: Checked with the site's own test files: a 1 kHz sine at -6 dBFS reads 1000.0 Hz and -6.0 dBFS; the 50 Hz and 60 Hz hum files give the right verdict and pink noise gives none.