Audio analyzers · Guide

Audio frequency chart and EQ cheat sheet

Every sound you hear sits somewhere between 20 Hz and 20,000 Hz. This chart shows where the bass, mids and treble are, where each instrument and voice lives, and what to cut or boost when a mix sounds muddy, boxy or harsh. Tap a band to hear it.

Try it

Tap a band to hear it and read EQ tips. Zoom with the buttons or Ctrl + scroll, then drag to move along.

20 Hz – 20 kHz
Main notes (fundamentals)Overtones and detail

Pick a band

Tap one of the 7 bands to hear a few seconds of noise filtered to that band. Start with your volume low.

The 7 frequency bands

Sound engineers split the range of hearing into 7 rough bands. The edges are not exact laws, and two charts may differ by a few hertz, but the names help you talk about a sound and find a problem fast. Each band below has the same three parts: how it sounds, what goes wrong, and the EQ move that usually helps.

Remember that the bands are not equal in width. Bass covers 190 Hz, while brilliance covers 14,000 Hz, yet both are about two octaves wide. Our ears hear in octaves (each one doubles the frequency), which is why the chart above uses a log scale.

Sub-bass (20–60 Hz)

How it sounds: a deep rumble you feel in your body. Pipe organs, 808 kicks, film explosions and synth bass reach down here.

Problems: too much sub-bass makes a mix boom on big speakers and uses up headroom, so the whole song has to be turned down. Most phone speakers and laptops cannot play this band at all, so you may not hear the problem.

EQ move: use a high-pass filter at 30 to 40 Hz on vocals, guitars, keys and overheads. Keep this band for the kick and bass only, and check it on headphones.

Bass (60–250 Hz)

How it sounds: the weight of the kick drum and bass guitar, the low notes of a piano and the warmth of a male voice.

Problems: too much sounds boomy and slow. Too little sounds thin, like a small radio. A kick and a bass that both peak at the same spot fight and blur.

EQ move: give each low instrument its own home. For example, boost the kick a little at 60 Hz and cut it at 100 Hz, then do the opposite on the bass.

Low mids (250–500 Hz)

How it sounds: body and fullness. The low strings of a guitar, the chest of a voice and the shell of a snare drum live here.

Problems: almost every instrument puts energy in this band, so it fills up fast. When it does, the mix sounds muddy, cloudy or blurred.

EQ move: cut 2 to 4 dB around 250 to 400 Hz on a few busy tracks, such as rhythm guitar, keys and pads. Small cuts on several tracks work better than one big cut on the mix.

Mids (500 Hz–2 kHz)

How it sounds: the core of most instruments. Vowel sounds of speech, the tone of a guitar and the punch of a snare sit in this band.

Problems: too much around 500 to 800 Hz sounds boxy, like a cardboard box. Too much near 1 kHz sounds honky or nasal. Too little makes a track sound far away.

EQ move: sweep a narrow boost slowly through the band until the ugly tone jumps out, then turn that boost into a cut of 2 to 3 dB.

Upper mids (2–4 kHz)

How it sounds: attack and bite: the pick on a guitar string, the snap of a snare and the clarity of words.

Problems: the ear is most sensitive around 3 kHz, so a small excess quickly sounds harsh and tiring, especially at high volume.

EQ move: cut 1 to 3 dB around 2.5 to 4 kHz on the harshest track. If the vocal gets lost, cut the guitars there instead of boosting the voice.

Presence (4–6 kHz)

How it sounds: edge and nearness. A small lift here makes a voice sound as if it is right in front of you.

Problems: too much sounds sharp and brittle. Too little makes the mix dull and distant.

EQ move: a wide boost of 1 to 2 dB at 5 kHz on the lead vocal often does more than a louder fader.

Brilliance (6–20 kHz)

How it sounds: air and sparkle: cymbals, breath and the hiss of the letters s and t.

Problems: too much makes the s sounds spit (sibilance) and brings up hiss. Many adults hear little above 15 kHz, so it is easy to boost this band too far without noticing.

EQ move: add a gentle shelf boost of 1 to 3 dB above 10 kHz for air, and use a de-esser for sibilance instead of a wide cut.

Instrument and voice ranges

The table lists the main notes (the fundamentals) of 25 common instruments and voices, plus how high their overtones reach. Overtones are the quieter tones above each note that give an instrument its own colour, so a piano and a violin playing the same 440 Hz A still sound different. You can see them for yourself with the overtones of an instrument tool.

Instrument or voiceMain notesOvertones up to
Kick drum40–100 Hz5 kHz (beater click)
Snare drum150–250 Hz10 kHz
Toms60–300 Hz6 kHz
Cymbals and hi-hat300–600 Hz16 kHz
808 and synth bass30–120 Hz3 kHz
Bass guitar41–392 Hz5 kHz
Double bass41–294 Hz4 kHz
Tuba37–349 Hz3 kHz
Trombone82–698 Hz5 kHz
French horn62–698 Hz4 kHz
Trumpet165–988 Hz10 kHz
Alto saxophone139–831 Hz8 kHz
Clarinet147–1,865 Hz8 kHz
Flute262–2,093 Hz10 kHz
Cello65–880 Hz8 kHz
Violin196–2,637 Hz10 kHz
Acoustic guitar82–988 Hz12 kHz
Electric guitar82–1,319 Hz6 kHz (amp speaker)
Piano27.5–4,186 Hz12 kHz
Bass singer82–330 Hz8 kHz
Tenor singer131–523 Hz8 kHz
Alto singer175–698 Hz10 kHz
Soprano singer262–1,047 Hz10 kHz
Male speech85–180 Hz8 kHz
Female speech165–255 Hz10 kHz

Three things stand out. First, very few instruments play notes above 2 kHz: everything up there is overtones, breath, bow noise and the click of a beater. That is why the treble controls clarity and air rather than pitch. Second, the low mids from 200 to 500 Hz hold the notes of nearly every instrument at once, which explains why mud is the most common mix problem.

Third, voices overlap guitars and keys almost exactly. A vocal that gets lost does not always need more level; often the guitars just need a small cut where the voice is strongest, around 1 to 4 kHz.

The ranges in the table are practical ones. A skilled player can go a little higher, a 5-string bass goes lower (down to 31 Hz), and drums change with tuning. Use the numbers as a starting point for EQ, then trust your ears and the analyzer.

Common EQ fixes

Most mix problems have a name and a usual place. Find the place first, then make a small change and listen again. Cuts usually sound more natural than boosts, and 2 to 3 dB is often enough.

Mud (200–500 Hz)

The mix sounds thick and blurred, and instruments seem to melt together. Cut 2 to 4 dB with a wide bell around 300 Hz on guitars, keys, pads and backing vocals. Leave the bass and kick alone at first. If the mix then sounds thin, you cut too much or on too many tracks.

Boxiness (500–800 Hz)

A drum, a voice or an acoustic guitar sounds as if it was recorded inside a cardboard box. Use a narrow boost to find the exact spot, which is often near 600 Hz, then cut it by 2 to 4 dB. Small untreated rooms add boxiness to recordings, so moving the mic away from a wall can help too.

Harshness (2–5 kHz)

The song is tiring after a minute, cymbals hurt, and loud guitars sound like a buzz saw. Cut 1 to 3 dB around 3 kHz on the harshest track rather than on the whole mix. Check at low volume as well: harshness is easiest to judge when the mix is quiet.

Sibilance (5–9 kHz)

The s, sh and t sounds of a singer spit and jump out. A de-esser turns down only those short moments, so the voice keeps its air. Set it around 6 to 8 kHz for most voices; female voices often sit a little higher than male voices.

Check your own mix with an analyzer

A chart tells you where things usually are; an analyzer shows where they really are in your track. Play your mix into the live spectrum analyzer and look for a hump that stands far above its neighbours, for example a bump at 300 Hz that is 6 dB higher than the rest. Press "Open in analyzer" on a band above to jump straight to that range.

For a quick look at the tonal balance, the RTA groups the sound into 1/3-octave bars, so a mix that is too bright or too heavy is easy to spot. Compare your mix with a song you like in the same style. You can read more in using an analyzer for mixing. Always use your ears for the final call: the graph shows what is there, not what sounds good.

FAQ

What frequency is bass?

Bass is roughly 60–250 Hz. Sub-bass, which you feel more than hear, is 20–60 Hz.

What is the frequency range of the human voice?

Speech fundamentals sit around 85–180 Hz for men and 165–255 Hz for women. Consonants and clarity reach 2–8 kHz.

Where is "mud" in a mix?

Usually 200–500 Hz. A small cut there on a few tracks often clears the mix.

What frequencies cause harshness?

Mostly 2–5 kHz, where the ear is most sensitive.

What is the range of human hearing?

About 20 Hz to 20 kHz for young people. The top end falls with age.

Written and tested by the SpectrumAnalyzer.app team · Last checked

How we tested: Each band sample was checked with the browser's own filter response: it passes its band (6 dB down at the edges) and is about 25 dB quieter one octave outside it. Instrument ranges follow standard note ranges with A4 = 440 Hz.