RF spectrum trace viewer (CSV)

Open a CSV trace from your spectrum analyzer or SDR to plot it, mark peaks, compare scans and check a limit line.

No file open yet

Drop a CSV or TXT trace here

From a tinySA, Rigol, Siglent, Keysight, RF Explorer, hackrf_sweep or rtl_power. The file is read on this device and never uploaded.

Peak at—
Peak level—
Limit lineOff
Channel power—

Traces
    Chart shows

    Open several files at once, or one after another with “Add a trace”, to compare up to 4 traces.

    Peaks

      Top 10 peaks in the part of the trace on screen. Click one to put the active marker on it.

      Markers
      Active marker

        M2, M3 and M4 also show their distance from M1 (Δ). With two or more traces, the list above gives the difference between the traces at the active marker.

        Limit line

        Levels are in the unit the chart shows. Two points at the same frequency make a step.

        Channel power
        Leave empty to use the RBW in the file.

        View
        Impedance (for dBµV and dBmV)

        Zoom with + and −, Ctrl + wheel or two fingers; drag or Shift + wheel to pan; double-click for the whole trace.

        Columns

        Open a file to see how it was read.

        File facts
        Export and share

        The clean CSV has the frequency in Hz and one column per trace in the chart's unit. The link keeps your settings and limit line, never your file.

        Your files never leave your device. Nothing is uploaded. P peakN next← → marker+ − zoom0 all

        How to use the trace viewer

        1. Save a CSV from your device. On a tinySA, use tinySA-App or QtTinySA on the PC and save the trace as CSV. On a Rigol DSA or a Siglent SSA, save the trace as CSV to a USB stick from the Storage or Save menu. Keysight and Agilent analyzers save "Trace (CSV)" the same way. RF Explorer for Windows exports CSV from its File menu. For rtl_power and hackrf_sweep, the output file is already CSV.
        2. Press Open CSV (or drop the file on the tool). The layout and units are found on their own, and the status line says how the file was read.
        3. Read the peaks. Marker M1 sits on the highest peak and the Peaks list shows the top 10. Click the chart to move the active marker, or press Peak and Next peak.
        4. Compare and check. Add up to 4 traces, turn on a limit line, or switch on Measure range and drag across a signal to get its channel power.
        5. Save the result as a PNG for a report or a forum post, or as a clean CSV for a spreadsheet.

        If a file is read wrongly, open Columns: pick the frequency and level columns and their units, then press Read again. No file at hand?

        How to read markers, peaks and limit lines

        M1 94.500 MHz −38.0 dBm M2 101.100 MHz −45.0 dBm limit line −50 dBm channel noise floor about −95 dBm 88 MHz → 108 MHz · ΔM2−M1: 6.600 MHz, −7.0 dB · limit: FAIL
        Markers read the exact points of the trace; the dashed line is a limit line, the shaded band a channel power range.

        A marker reads one point of the trace: its frequency and its level. M1 starts on the highest peak. M2, M3 and M4 also show a delta (Δ): how far they are from M1 in frequency and in dB. In the example, two FM stations sit 6.6 MHz apart and the second is 7 dB weaker. Markers use the real points in the file, so the reading is exactly what your analyzer measured, with no smoothing.

        The peak table lists the 10 strongest peaks on screen. A peak only counts when it stands out from the trace around it by the amount you set (6 dB to start with), so the ups and downs of the noise floor are not listed. Zoom in and the table follows the part you are looking at.

        A limit line is a pass/fail mask. Type its corner points, draw a flat line, or make one from trace 1 plus a margin (a "golden" trace). Every point above the line turns coral and the readout says FAIL, with the worst point and how many dB it is over. When everything passes, it shows how close the trace came.

        Channel power adds up the power of every point in a range and corrects for the point spacing and the RBW (resolution bandwidth, the width of the analyzer's filter). A signal 20 MHz wide that reads −62 dBm in a 300 kHz RBW has a total power of about −44 dBm. To see what your analyzer can hear at all, work out its noise floor from the RBW.

        Use cases

        Compare antennas

        Scan the same band twice, once with each antenna, and save both traces. Open them together: the second trace gets its own colour, and "Difference vs trace 1" shows the gain of one antenna over the other across the band. A whip that reads −71 dBm at 433.92 MHz against −63 dBm for a tuned dipole is 8 dB worse, and the difference view shows whether that holds over the whole band.

        EMI pre-check with a limit line

        Before paying for a test lab, scan your device with a near-field probe and set a limit line a few dB under the level you must meet, for example a flat line at −60 dBm from 30 to 230 MHz. Any spur over it is marked, and the readout gives its frequency, such as a clock harmonic at 144.000 MHz that is 4.2 dB over. This is a pre-check only: a real emissions test needs a calibrated set-up and an antenna at a fixed distance.

        Share a scan in a forum

        A photo of an analyzer screen is hard to read. Open the CSV here, put M1 and M2 on the signals in question, and save the PNG: it has the trace, the markers, the top peaks and the file name. Or save the clean CSV, which any spreadsheet opens with the frequency in Hz and the level in dBm.

        rtl_power heat map

        rtl_power can scan a wide band for hours with a cheap USB dongle. Open its CSV and every sweep becomes one row of a heat map, so a signal that appears now and then shows up as a bright mark. The trace above it shows the average, max hold, min hold or last sweep. A 100 MB file is read in the background with a progress bar; very long scans are folded to 1,024 rows, keeping the strongest level of each group of sweeps.

        Supported formats

        SourceWhat the file looks likeLevels
        tinySA, tinySA Ultra (tinySA-App, QtTinySA)Frequency and level columns, with or without a header linedBm
        Rigol DSAA settings block (start, stop, RBW, reference level), then frequency and amplitude rowsdBm, dBµV and others
        Siglent SSAA settings block, then rows with frequencies often in scientific notationdBm, dBµV and others
        Keysight / AgilentA header block, a DATA line, then frequency and level rows; several traces as extra columnsdBm, dBµV and others
        RF ExplorerFrequency (MHz) and level columns, or one sweep per row with the start and step at the topdBm
        rtl_power, hackrf_sweepDate, time, low and high frequency, step, samples, then the levels of that part of the sweepdB (relative)
        Any other CSV or TXTPick the columns and units under ColumnsdBm, dBµV, dBmV, dBW, mW, W, V

        Comma, semicolon, tab and space separators all work, also with decimal commas (88,5) and units written next to the numbers (88.5 MHz). Be aware that the makers change their export layouts between firmware versions, and we built these readers from manuals and shared sample files, not from every model. If your file opens wrongly, the column picker fixes it, and we would like to see the file: send it through the contact page.

        The viewer only shows what is in the file: the accuracy is that of your analyzer. For which analyzer to buy, see the best spectrum analyzers, read the tinySA guide, or plug in a dongle for a live RTL-SDR spectrum. More tools are on the RF tools page.

        FAQ

        Which devices are supported?

        tinySA and tinySA Ultra, Rigol DSA, Siglent SSA, Keysight/Agilent CSV, RF Explorer, hackrf_sweep and rtl_power. Other CSVs work with the column picker.

        Is my file uploaded?

        No, it is read in your browser only.

        Can I compare two scans?

        Yes, up to 4 traces with their own colours, and a difference marker.

        What is a limit line?

        A pass/fail mask; any point above it is flagged, useful for quick emissions checks.

        Written and tested by the SpectrumAnalyzer.app team · Last checked

        How we tested: Checked with the site's own sample traces: the tinySA file gives peaks at 94.500, 101.100 and 105.300 MHz (−38, −45 and −52 dBm), the Rigol file 433.920 MHz at −20.0 dBm and 446.020 MHz at −48.0 dBm, and the Siglent file 2450.000 MHz at −30.0 dBm and 2480.000 MHz at −55.0 dBm, with the WiFi channel 1 hump found by channel power.