Harmonics and intermodulation calculator
Type two or three frequencies to list every harmonic and mixing product up to order 9 and see which ones land in your band.
For mic plans, about your receivers' channel width.
IP3 helper
| Frequency | Product | Order | Note |
|---|
How to use the intermodulation calculator
- Type f1 and f2, and f3 if a third signal is present, and pick the unit.
- Choose the Highest order: 3 or 5 for most work, up to 9 for strong signals or sensitive receivers.
- Enter the Band you care about, such as a receiver's range or your mic channels.
- Read the counts and the chart, then filter the table to In band or Hits. Save the CSV or share the link.
Worked example: 100 and 101 MHz
Two transmitters at 100 and 101 MHz pass through the same amplifier. The third-order products are 2 × 100 − 101 = 99 MHz and 2 × 101 − 100 = 102 MHz, one spacing below and above the pair. Fifth order gives 3 × 100 − 2 × 101 = 98 MHz and 103 MHz, seventh order 97 and 104 MHz, and ninth order 96 and 105 MHz. With the band set to 95 to 105 MHz, the calculator finds 8 products in the band, the lowest of order 3.
The even orders land far away: f2 − f1 = 1 MHz, f1 + f2 = 201 MHz and the harmonics 2f1 = 200 MHz and 2f2 = 202 MHz. That is why even orders rarely bother a narrow band, while odd orders sit right next to the signals that made them. Press to see it with all orders up to 9.
In the chart, the green lines are your inputs, amber lines are products inside the band and red lines are products that land on an input. Outside the band, pale blue lines are even orders and pale red lines odd orders. The taller a line, the lower its order, and lower orders are usually the stronger ones, because the higher-order parts of an amplifier's response are usually weaker. The table lists the same products by frequency with the band and hit notes; the CSV holds every product, so you can sort it in a spreadsheet.
Use cases
Wireless mic frequency plans
Every pair of mics makes 2f1 − f2 products, and every three make f1 + f2 − f3. With three mics at 606.000, 606.400 and 607.200 MHz, 2 × 606.400 − 606.000 lands on 606.800 MHz, which is clear, but 2 × 606.400 − 607.200 = 605.600 MHz would hit a fourth mic placed there. Enter three mic frequencies, set the hit tolerance to your receivers' channel width, and move any mic that shows a hit.
Repeater sites
Towers with several transmitters suffer intermodulation in the transmitters' output stages, and also in rusty bolts, loose connectors and old cables, which act as weak non-linear junctions. If two transmitters at 152.3 and 154.1 MHz share a site, their third-order products at 150.5 and 155.9 MHz can block a receiver on either frequency. The list tells you which products to look for on a spectrum analyzer.
Receiver design
Two strong out-of-band signals can mix in a receiver's front end and drop a product right on the wanted channel. Put the two strongest signals near your receiver in f1 and f2, the receive band in Band, and use the IP3 helper to see how strong the IM3 product will be. If it is above the noise floor, the receiver needs a filter in front, or an amplifier with a higher IIP3.
IP3 in plain words
Turn up two tones by 1 dB and each IM3 product grows by 3 dB, so it catches up 2 dB on the tones. Draw both on a graph and the lines would cross at a point called the third-order intercept: IIP3 is that point measured at the input, OIP3 at the output (OIP3 = IIP3 + gain). Real amplifiers compress before they get there, so IP3 is a figure on paper, but it predicts the products well when the tones are at least 10 dB below it. The rule is IM3 = 3 × Pin − 2 × IIP3. With −20 dBm per tone and an IIP3 of +10 dBm, IM3 is −80 dBm at the input, 60 dB under each tone. Add 10 dB to IIP3 and the products drop by 20 dB.
Formula
A product is f = m × f1 + n × f2 + p × f3, where m, n and p are whole numbers (positive, negative or zero) and the order is |m| + |n| + |p|. Order 2 gives f1 + f2, f2 − f1 and the second harmonics; order 3 gives 2f1 ± f2, 2f2 ± f1, f1 + f2 − f3 and the third harmonics. Only products above 0 Hz are listed. The list grows fast: two inputs give 10 products up to order 3 and 88 up to order 9 (harmonics included), and three inputs give 576 up to order 9. For signals that fold back because of sampling rather than mixing, see aliasing. To add up the noise of a whole receiver chain, use the noise figure calculator. More tools are on the RF tools and calculators page.
FAQ
What is intermodulation?
New unwanted frequencies made when two signals mix in a non-linear part, like an amplifier.
Why is 3rd order the worst?
Products like 2f1 − f2 land close to the original signals, often inside the same band.
What is IP3?
A figure of merit: the higher the third-order intercept point, the weaker the IM3 products.
Can it plan wireless mic frequencies?
Yes. Enter the mic frequencies and check that no products land on another mic.