Morse code decoder from audio (CW)

Turn Morse beeps into text, live from your mic or from a recording. Speed and tone are found on their own.

Press Listen, or open a recording

Hold your phone or laptop near the speaker. The browser asks to use your microphone; your sound stays on this device.

Or drop a file here.

Decoded text appears here.
Tone—
Speed—
Signal over noise—

Tone

Or click a peak on the small spectrum. With the spectrum focused, the arrow keys move the tone by 5 Hz (with Shift by 50 Hz).

Decoder
How far a beep must rise above the noise. Raise it when noise turns into stray E, I and T letters.
Gap timing

The speed is found on its own from 5 to 50 WPM. The chips at the top set the filter width: narrow keeps out noise and nearby signals, wide follows fast Morse (above 30 WPM use 100 Hz or wider).

Source

Video files work when the browser can open their sound (mp4 and webm in most browsers). Files are read on this device only; they are never uploaded.

Export and share

The share link holds the settings only, never the sound or the text.

Sound never leaves your device. Nothing is uploaded. Space listenC copyX clearA auto tone

How to use the Morse decoder

  1. Press Listen and allow the microphone, then play the Morse sound from a radio, a speaker or another device. Keep the mic about 30 cm from the speaker.
  2. For a recording, choose Audio or video file as the source and open it, or drop it on the tool. The whole file is decoded at once, and you can press play to follow it on the timeline.
  3. Wait a few beeps. The decoder finds the tone (it shows as an amber band on the small spectrum) and learns the speed by itself.
  4. Read the text in the box. Press Copy text or Save .txt to keep it.
  5. If the text looks wrong, click the right peak on the small spectrum, then raise the Threshold in the Decoder settings.

No Morse sound at hand?

How to read the decoder

tone 700 Hz: the amber band is the filter weaker signal (990 Hz) PARIS tone level threshold time → · dots amber, dashes coral, letters under the bars
The word PARIS at 20 WPM: one dot is 60 ms, a dash is 180 ms.

The tone and the small spectrum

Morse on a radio or in a recording is one beep at a single pitch, usually between 400 and 1,000 Hz. The small spectrum shows every pitch from 100 Hz to 3 kHz, and the tall peak is the Morse tone. The amber band around it is the tone filter. Only sound inside that band counts, so a second station 300 Hz away, or a voice, is ignored. Click another peak to move the filter there.

The threshold

On the timeline, the blue line is the level of the tone and the dashed line is the threshold. A beep starts when the blue line goes above the dashed line and stops when it falls under it. The threshold follows the signal when it fades, and it never drops into the noise: a beep must be at least as many dB over the noise as the Threshold setting says (8 dB to start with).

The speed (WPM)

Speed is shown in words per minute. One word is the word PARIS, which is 50 dot lengths long, so a dot lasts 1,200 ÷ WPM milliseconds: 60 ms at 20 WPM and 24 ms at 50 WPM. The decoder sorts the beeps into short and long ones and the gaps into three sizes, so it follows a sender who speeds up or slows down. When the letters are fast but the gaps are long (Farnsworth timing, common in Morse lessons), the readout shows both speeds, for example 18 / 8 WPM.

SpeedDotDashGap between words
5 WPM240 ms720 ms1.68 s
13 WPM92 ms277 ms646 ms
20 WPM60 ms180 ms420 ms
35 WPM34 ms103 ms240 ms
50 WPM24 ms72 ms168 ms

Use cases

Ham radio practice

Put your phone next to the receiver while you listen to a CW contact or the practice broadcasts some clubs send. Copy by ear first, then compare with the text box. If you wrote down "CQ CQ DE" and the decoder agrees, your ear is right. At 25 WPM and above, choose the 100 or 200 Hz filter so the short dots are not smeared together.

Puzzle and escape-room audio

Geocaches, escape rooms and online puzzles often hide a word in a clip of beeps. Open the audio or video file and the whole message is decoded in a second or two. If the beeps are on a tone higher than 3 kHz or mixed with music, click the beep's peak on the small spectrum and the file is decoded again at that tone.

Old recordings

Tapes of ship radio, aircraft beacons or a relative's old ham contacts are often noisy and fade in and out. The decoder's level follower holds on through fades of 10 dB or more. For a hissy tape, use the 50 Hz filter and raise the threshold to 12 dB, then save the timing CSV if you want to study the sender's style.

Learning Morse

Practice sending with a key and a buzzer, or with an app, and let the decoder read it back. Clean sending gives clean text; a "#" means a pattern that is not a Morse letter, often a dash sent too short or a gap left out. Watch the timeline: dashes should be about three dots long, and the gap between letters three dots too.

Tips for clean decoding

  • Use the file when you have it. Opening a recording is cleaner than playing it into the mic, because room echo and fan noise never get in. If you want the sound of a video, open the video file, or share the tab where it plays.
  • Turn the speaker up, not the mic. A clear beep 30 dB over the room noise decodes well. The Signal over noise readout should show at least 15 dB.
  • Pick the right filter width. 100 Hz suits most Morse. Go to 50 Hz in noise or when two stations are close, and to 200 or 400 Hz for fast Morse or a tone that drifts.
  • Raise the threshold for noise. If stray E, I and T letters appear between words, noise is crossing the threshold. Raise it a few dB.
  • Give it a few letters. The speed is learned from the first beeps, so the first one or two letters can be wrong live. A file is read twice, so the start is right there too.

Hand-sent Morse with uneven gaps can still split a word in two or join two words. To see the signal itself, see the signal on a spectrogram, where each beep is a short line at the tone's pitch.

Prosigns and unknown signs

Prosigns are two letters sent as one sign, with no gap between them. The decoder shows them in square brackets: [AR] end of message, [SK] end of contact, [BT] a break between parts (also written as =), [KN] "only the station I called may answer", [AS] wait, [KA] start of message and [SN] understood. [SOS] is the distress signal, and [HH] is the error sign (eight dots), which means "ignore the last word". A pattern that is not in the Morse table is shown as #. For phone keypad beeps rather than Morse, use the DTMF decoder. All decoders are listed on the signal decoders page.

FAQ

Can it decode Morse from a video?

Yes, if your browser can open the video's audio. Open the video file here, or play it aloud and use the mic.

What speeds work?

About 5 to 50 words per minute. The speed is found automatically.

Why is the text wrong?

Noise, fading or two signals. Pick the tone on the mini spectrum and set the threshold higher.

What are prosigns?

Joined codes like AR (end of message) and SK (end of contact). They appear in brackets.

Written and tested by the SpectrumAnalyzer.app team · Last checked

How we tested: Checked with the site's own test file: Morse 'PARIS PARIS PARIS' at 20 WPM on a 700 Hz tone decodes as PARIS PARIS PARIS, with the speed read as 20 WPM and the tone found at 700 Hz.