VSWR and return loss calculator
Type a VSWR, return loss, reflection coefficient, mismatch loss or reflected power and get the other four with a plain verdict, or start from a load impedance.
Type in any box
Or start from a load impedance
Type R or X to work from the load.
Optional
VSWR 1.50:1. Good match. Nothing to fix.
- 4 % of the power is reflected and 96 % reaches the load (mismatch loss 0.177 dB).
How to use the VSWR calculator
- Type the number you have into its box: the VSWR from an SWR meter, the return loss from an antenna analyzer or VNA (S11 such as −14 dB works too), or any of the other three.
- To start from an impedance instead, type the load's resistance R and reactance X and pick the line impedance Z0.
- Add the forward power to see the watts that come back, or the cable loss to see what the radio end of the cable shows. Then copy the results or share the link.
Worked example: VSWR 1.5
Your SWR meter shows 1.5:1. The reflection coefficient is Γ = (1.5 − 1) ÷ (1.5 + 1) = 0.5 ÷ 2.5 = 0.2. That is the share of the voltage that bounces back from the antenna. Power goes with the square of the voltage, so 0.2² = 0.04: 4 % of the power is reflected.
Return loss is the same thing in decibels: −20 × log10(0.2) = 13.98 dB, usually rounded to 14 dB. Mismatch loss is how much less power reaches the antenna: −10 × log10(1 − 0.04) = 0.18 dB. With 100 W forward, 4 W comes back and 96 W reaches the antenna. A 75 Ω load on a 50 Ω cable gives exactly this result, since Γ = (75 − 50) ÷ (75 + 50) = 0.2. Type 75 into the resistance box and you will see VSWR 1.5 again.
The other boxes work the same way. An antenna analyzer that shows 20 dB of return loss (S11 = −20 dB) means Γ = 0.1, VSWR 1.22:1 and only 1 % reflected. A complex load works too: 25 + j25 Ω on a 50 Ω line gives Γ = 0.447 at 116.6°, which is VSWR 2.62:1. The positive angle tells you the load is inductive. A series capacitor that cancels the +j25 Ω would leave 25 Ω and bring the VSWR down to 2:1.
What VSWR means for your antenna
VSWR tells you how well the antenna's impedance matches the cable and the radio, which are almost always 50 Ω. When they match, all the power goes into the antenna. When they do not, part of it bounces back down the cable, and the forward and reflected waves add up to a "standing wave" whose voltage peaks are higher than normal.
The lost signal itself is small. Even at 2:1, 11 % of the power is reflected and the antenna gets only 0.51 dB less, which nobody at the other end will notice. At 3:1 it is 25 % and 1.25 dB. The bigger concern is the radio: the reflected power heats its output stage, and many transmitters turn their power down when the SWR rises.
A high or changing VSWR is also a clue. A wrong antenna length moves the best match to another frequency, so measure across the whole band. Water in a connector or a crushed cable makes the reading jump. And some antennas never reach 1:1 on their own: a half-wave dipole is about 73 Ω, which gives roughly 1.46:1 on 50 Ω coax. To cut an antenna to the right length, use the antenna length calculator.
Formulas
- Reflection coefficient from VSWR: |Γ| = (VSWR − 1) ÷ (VSWR + 1), and back: VSWR = (1 + |Γ|) ÷ (1 − |Γ|).
- Return loss: RL = −20 × log10(|Γ|) dB, so |Γ| = 10−RL / 20.
- Reflected power: |Γ|² × 100 %. Mismatch loss: −10 × log10(1 − |Γ|²) dB.
- From a load impedance Z = R + jX on a line Z0: Γ = (Z − Z0) ÷ (Z + Z0), worked out with complex numbers. Its size gives the VSWR and its angle shows whether the load looks inductive or capacitive.
- Through a cable with L dB of loss, the reflection seen at the radio is |Γ| × 10−2L / 20, because the reflected wave crosses the cable twice.
Limits
A long or lossy cable makes any antenna look better than it is. A 3:1 antenna at the end of a cable with 3 dB of loss reads only 1.67:1 at the radio, while half the power is already lost as heat in the cable. Measure at the antenna end when you can. Cheap SWR meters can also be off at low power or on frequencies they were not built for, and VSWR says nothing about how well the antenna radiates: a dummy load has a perfect 1:1 and radiates almost nothing. To turn the watts into dBm, use the dBm converter. More tools are on the RF tools page.
FAQ
What is a good VSWR?
1.5:1 or lower is good; up to 2:1 is acceptable for most radios.
How is return loss related to VSWR?
Higher return loss means a better match: 20 dB return loss is about VSWR 1.22.
Does high VSWR damage a transmitter?
It can over time, as reflected power heats the output stage. Many radios reduce power to protect themselves.
Can a tuner fix VSWR?
It fixes what the radio sees, but losses in the feed line stay.