Room acoustics
Room acoustics tools
A room changes every sound you play in it: it adds echo, piles up some bass notes and swallows others. These tools measure how long your room rings, predict its bass problems from its size and give the exact bands acousticians work in. To see the whole balance at your seat, add the 1/3-octave RTA with pink noise.
- RT60 Reverb Time MeterClap or pop a balloon to measure a room's reverb time per octave band.
- Room Mode CalculatorType a room's size to see its bass modes and problem frequencies.
- Octave Band CalculatorExact and nominal centres and edges for 1/1 to 1/24 octave bands.
- Room EQ GuideMeasure, place the speakers and seat, then EQ only the peaks that are left.
The two big room problems: echo and boomy bass
Almost every untreated room has the same two faults, and they need different fixes.
Echo, or too much reverb. Hard walls, a bare floor and a glass window bounce sound around for a long time after it stops. You hear it when you clap: a hiss or a ring that hangs in the air. The number for it is the reverb time, RT60: how long the sound takes to fade by 60 dB. A small home studio wants about 0.2 to 0.4 seconds and a living room about 0.4 to 0.6. A bare room often reads 0.8 seconds or more, so speech blurs, mixes sound washed out and every word in a video call comes with a tail. Soft materials fix it: panels, rugs, curtains, a sofa, full bookshelves.
Boomy bass, or room modes. Low notes have long waves, 3.4 m at 100 Hz and 6.9 m at 50 Hz. Between two parallel walls they bounce back and forth and add up, so some notes boom at the seat while others almost vanish. Move your head 50 cm and the bass can change by 10 dB. These modes sit at frequencies set by the room’s length, width and height, so you can work them out before you buy anything. Thin panels do almost nothing here, because a 5 cm panel is tiny next to a 3 m wave.
The reverb time (RT60) meter measures the first problem with a clap or a balloon pop, band by band. The room mode calculator lists the second from your room size, and the octave band calculator gives the exact band edges both of them use.
Measure first, then treat
Treating a room by guesswork wastes money, so work in this order and measure after each step.
- Measure the reverb time. Take five claps or balloon pops from different spots and note the RT60 at 500 Hz and 1 kHz, and in the 125 Hz band.
- Find the room modes. Enter the room size and note the first few modes below 200 Hz. Play those notes with a sine tone and listen at your seat.
- Set the speakers and the seat. Moving the seat away from the middle of the room, and the speakers away from the walls, often helps the bass more than anything you can buy.
- Tame the echo. Put acoustic panels at the first reflection points on the side walls and the ceiling, then measure the reverb time again.
- Treat the bass. Thick corner bass traps soak up the low modes that panels miss. Check the 125 Hz band again after you add them.
Small rooms rarely need more than 15 to 25 % of the wall area covered. Too much soft material makes a room sound dead and dull, so stop when the reverb time reaches the target for your room type.
We may earn a commission if you buy through these links. It does not change the price.
How these tools work in your browser
The reverb meter records the clap with your microphone and analyses it on your device; no sound is uploaded and the mic turns off after each shot. The calculators need no microphone at all, just numbers. Phone and laptop mics are good enough for reverb time in the mid and high bands. Below about 100 Hz they are less sensitive, so use a balloon pop rather than a clap, take a few shots, or use a USB measurement microphone for the deep bass.
FAQ
What is a good reverb time for a home studio?
About 0.2 to 0.4 seconds for a small control room. Living rooms are often 0.4 to 0.6 seconds.
Why is my bass boomy in one spot?
Room modes: bass waves bounce between walls and pile up at some spots. The room mode calculator shows where.
Do foam panels fix bass?
No. Thin foam only tames mid and high echoes. Bass needs thick traps in the corners.
Can I measure a room with my phone?
Yes for reverb time and a rough bass picture. A measurement mic gives more reliable low-bass results.