Speaker polarity test

Play a click on one speaker, let your mic listen, and see if the speaker is wired in phase or reversed.

LeftNot tested
RightNot tested
BothNot tested

Choose a speaker, then press Start

Hold the mic 30–50 cm in front of that speaker. It plays 8 short clicks at a low level. Your sound stays on this device.

Result—
Confidence—
Delay—
Signal to noise—

Check your mic first

Some USB mics flip polarity. Test a speaker you know is wired right first. If it reads Reversed, switch this on and every result is flipped back.

Test clicks

Switch it off to test a car stereo, TV or PA: save the clicks below, play them there, press Start and it listens for 12 seconds.

The WAV has 16 clicks on the speaker chosen above (left, right or both).

Listening test

Sit between the speakers. In phase sounds full and centred; out of phase sounds thin, wide and hard to place.

Microphone

Sound is analysed on this device and never uploaded. Echo cancelling and auto gain are switched off where the browser allows.

Export and share
Recent results
    Sound never leaves your device. Nothing is uploaded. Space start/stopLRB speaker

    How to use the polarity test

    1. Set the volume low to medium. Choose Left, Right or Both for the speaker you want to check.
    2. Hold your phone or laptop mic 30 to 50 cm straight in front of that speaker, at the height of its woofer, the bigger cone.
    3. Press Start and allow the microphone. You hear 8 short clicks, half a second apart. Keep quiet while they play.
    4. Read the tile for that speaker: In phase or Reversed, with how sure the tool is. Then move to the next speaker and repeat.

    Do the mic check once first: test a speaker you trust, such as one you wired yourself. If it reads Reversed, switch on My mic is inverted.

    How to read the result

    first peak up first peak down In phase Reversed echoes echoes time after the click, a few milliseconds
    Only the first peak counts; the wiggles after it are echoes from the floor and walls.

    Each click is a short push of voltage in one direction. A speaker wired the right way pushes its cone out, so the air pressure at the mic rises first and the first peak of the averaged pulse goes up. A reversed speaker pulls its cone in, and the first peak goes down. The tool looks only at that first peak, the sound that comes straight from the speaker, and ignores the echoes that arrive a few milliseconds later.

    The confidence % says how much the 8 clicks agree, how one-sided the first peak is and how far it stands above the room noise. Under 60 % the tile says Unclear. Very small speakers often read Unclear, because they cannot play the low part of the click. The test listens between 150 Hz and 2 kHz, where the woofer works, because some speakers wire their tweeter in reverse on purpose as part of the crossover design. A delay over 120 ms, or the Bluetooth switch, marks the result as less reliable.

    The delay readout is the time from the click leaving this page to the sound reaching the mic, including the sound card on both ends. A few tens of milliseconds is normal for wired speakers. Both plays the click on the two speakers at once; the result then follows whichever speaker’s sound reaches the mic first, so it is a quick check of a pair you sit in the middle of, not a way to find which one is reversed.

    Use cases

    New home theatre install

    With five or seven speakers and long runs of cable behind the furniture, one swapped pair of wires is easy to miss. Test each speaker on its own with the mic 40 cm away; the front left and right can be done from this page, and the rest with the clicks saved as a WAV and played from a USB stick on the receiver, one channel at a time. A reversed centre speaker makes dialogue sound thin when it blends with the fronts.

    Car audio

    Door speakers are often replaced with new cables pushed through tight rubber boots, and the stripe on the wire is not always the same side. Play the saved WAV through the stereo, use the fader and balance to send it to one door at a time, switch off Play the clicks from this page and hold the phone near that door’s woofer. Reversed door speakers are a common reason for weak bass in the front seats.

    PA stacks

    When subwoofers and tops come from different cabinets or amps, check the polarity of each box before the show. Stand 50 cm in front of each cabinet with the clicks playing through the desk. If one sub reads Reversed, the pair will cancel in the bass right where the audience stands.

    The listening test

    You can also hear polarity. Sit in the middle, in front of both speakers, and open the Listening test in the settings. In phase plays the same pink noise from both speakers: it sounds full and seems to come from one spot in the middle. Out of phase flips the right speaker on purpose: the noise suddenly sounds thin, spread out and hard to place, and the bass gets weaker, because the two speakers cancel each other’s low notes.

    If the in-phase noise already sounds like the out-of-phase one, one of your speakers is reversed. Start with the noise level low; pink noise is louder than it seems. This test checks a pair, so use the click test above to find which speaker is the reversed one.

    How to fix reversed wiring

    Turn the amplifier off. At the reversed speaker, swap the two wires: the one on the red (+) terminal goes to the black (−) terminal, and the other way round. Speaker cable usually marks one conductor with a stripe, a ridge or printed text, so use that mark the same way at both ends of every cable. Then run the test again; the tile should now read In phase. If every speaker reads Reversed, check the mic setting first. For the speaker’s tone balance, run the frequency response test, and for a Bluetooth delay, the latency test. More tests are in the speaker and audio test tools.

    FAQ

    What happens if a speaker is out of phase?

    Bass cancels and the stereo image sounds wide and hollow.

    Is polarity the same as phase?

    Polarity is the + and − wiring; phase is timing. A reversed wire flips polarity.

    Does it work with Bluetooth speakers?

    Often, but processing inside them can confuse the result, so it is marked less reliable.

    How do I fix it?

    Swap the + and − wires on that one speaker.

    Written and tested by the SpectrumAnalyzer.app team · Last checked

    How we tested: Checked with made-up recordings of a speaker with floor and wall echoes, wired correctly and reversed, at several noise levels, and with the site's own test files for silence, steady tones and broken files.