Stereo phase and width meter
Open a stereo file or share tab audio to see phase correlation, width, a vectorscope and how much your mix loses in mono.
No file open yet
Drop a stereo file here to check its stereo image
wav, flac, mp3, m4a or ogg. The file is read on this device and never uploaded.
Reading the file…
0 %
Result
Open a stereo file or share tab audio to check the stereo image.
- File
- Open a stereo file to see its results.
Vectorscope
Lissajous: mono is a vertical line, left-only leans to L, right-only to R, and out-of-phase sound lies flat. Polar folds everything into a half circle, with out-of-phase sound at the edges. The scope zooms itself (“auto”). Press V to switch.
Why no microphone?
Almost every phone and laptop has one mic, or mixes its mics into one channel, so the meter would always read +1. To check a mix, open the stereo file, or play it in another tab and press Tab audio (Chrome or Edge on a computer).
Export
The CSV has correlation, the three band correlations, width, mono loss and level for every 200 ms.
Recent checks
How to use the stereo phase meter
- Press Open file or drop a stereo file onto the tool. The whole file is measured first, so the readouts and the graph show the full song straight away.
- Read Correlation, Width and Mono loss, and the verdict in the Result panel.
- Press Play to watch the vectorscope and the meters move with the music. Click the graph to jump to a moment where the line dips below zero.
- Check the three band meters: the Low one shows whether the bass stays centred.
- To check music that plays in another tab, press Tab audio and share that tab with its sound.
How to read correlation and the vectorscope
Correlation compares the left and right channels moment by moment. At +1 they are the same, so the sound is mono. Around +0.3 to +0.7 is a normal wide mix: the channels share a lot but not everything. Near 0 they have little in common, as with a pair of mics far apart or a heavy stereo widener. Below 0, one channel is partly upside down compared with the other, and those parts cancel when the two are added together.
Width is the share of side signal: 0 % is mono, 100 % means side and mid are equally strong, as with two unrelated channels, and over 100 % means more side than mid, which only happens with out-of-phase sound. Side vs mid gives the same balance in dB. Mono loss is how much quieter the mix plays when left and right are summed to one channel; a normal mix loses 1 to 3 dB, and a mix that is out of phase can lose 10 dB or vanish.
In the vectorscope, every dot is one moment of the sound. Mono is a vertical line, a wide mix is a round cloud, a sound only on the left leans towards L, and out-of-phase sound lies flat. The graph below shows the correlation over the whole file, with the bass correlation as a blue line.
Use cases
Mono check for club and phone playback
Many club systems are wired in mono, and many phones play from a single speaker. Before you send a track to a DJ, open it and look at the Low meter. If it reads +0.95, the kick and bass will survive. If the bass drops to −0.2 in the drop, a widener on the bass is fighting itself, and a mono club rig will lose the low end exactly where it matters.
Wide synths
A big pad with a stereo chorus can sound huge on headphones and thin on a laptop. Solo the pad, export it, and check it: a correlation that sits around +0.2 with dips below zero means it will lose level in mono. The mono loss readout tells you how much, for example 4.5 dB, so you can narrow the chorus until the loss falls to 1 or 2 dB.
Stereo mic pairs
Two mics on a piano or a choir pick up the same sound at slightly different times. With a spaced pair 60 cm apart, the bass reaches both mics almost in step, so the Low meter stays high, while the High meter can sit near 0, because the small delay is many waves long up there. A coincident (XY) pair has no delay between its mics and usually reads higher in every band, which makes it the safer choice when the recording must also work in mono.
Limits of the meter
Correlation shows how alike the channels are, not whether the mix sounds good: a dry vocal in mono reads +1 and is perfect, while some ambient music sits near 0 on purpose. A few short dips below zero, such as a reverb tail, are normal. Lossy files (MP3, AAC) can use joint stereo, which may change the side signal a little, so measure the WAV or FLAC master when you can. To see the two channels as an XY picture of a single tone, use the XY scope view of the oscilloscope.
Fixing phase problems
If the whole file reads −1 or close to it, one channel has its polarity flipped, often from a cable wired the wrong way or a plugin setting: invert the polarity of one channel and check again. If only the bass is wide, put a mono-maker or a mid/side EQ on the low end and keep everything under about 120 Hz in the middle. For a pair of mics, move one mic until the low band reads above +0.5, or nudge one track by a few milliseconds in your editor. After the fix, check the loudness with the LUFS meter, because a mix that no longer cancels can play louder in mono. More checks before release are on the audio file checks page.
FAQ
What is phase correlation?
How alike the left and right channels are: +1 is mono, 0 is very wide, below 0 means parts cancel in mono.
Why check mono?
Phones, clubs and many speakers play in mono; out-of-phase parts can disappear there.
Why is my bass out of phase?
Stereo wideners or chorus on bass are common causes. Keep the low end centred.
Can I use the mic?
Most phone and laptop mics are mono, so use a stereo file or tab audio.