DTMF tone decoder
Turn phone keypad beeps into digits, live from your mic or from a recording, with the time, twist and level of each key.
Press Listen, or open a recording
Hold the phone or speaker near your mic and press the keys. The browser asks to use your microphone; your sound stays on this device.
Or drop a file here.
Decoder
Digit list
| # | Time | Key | ms | Low | High | Twist |
|---|
Each decoded key is listed here with its start time, length, the frequency and level (dBFS) of both tones, and the twist in dB. Click a row to play a file from that key.
Source
Video files work when the browser can open their sound (mp4 and webm in most browsers). Files are read on this device only; they are never uploaded.
Export and share
The share link holds the settings only, never the sound or the digits.
How to use the DTMF decoder
- Press Listen and allow the microphone. Hold the phone, radio or speaker about 20 cm from the mic and press the keys or play the recording.
- For a saved call, a voicemail or a video, choose Audio or video file as the source and open it, or drop it on the tool. The whole file is decoded in a moment, and you can press play to follow the keys on the timeline.
- Watch the keypad picture: the key being heard lights up, and each digit is added to the text box and the Digit list with its time.
- Press Copy digits, Save .txt or save the Digit list (CSV).
- If a held key reads twice, raise the Minimum tone length. If keys from a mic recording are missed, choose Loose twist.
No keypad tones at hand?
How DTMF works
DTMF stands for dual-tone multi-frequency. A phone keypad has four rows and four columns, and each row and each column has its own tone. The rows are the low group: 697, 770, 852 and 941 Hz. The columns are the high group: 1,209, 1,336, 1,477 and 1,633 Hz. Press a key and the phone plays its row tone and its column tone at the same time, so 5 is 770 Hz plus 1,336 Hz and # is 941 Hz plus 1,477 Hz. The fourth column, A to D, is missing on most phones but is used in some radio and control systems.
The decoder checks the sound every 5 ms with eight Goertzel filters, one tuned to each tone. A Goertzel filter is a quick way to measure the level of a single frequency. A key counts only when exactly one low tone and one high tone stand out at least 10 dB above the other tones of their group, together make up most of the sound, sit within 3 % of the right frequencies, and last at least the minimum tone length. A key that stays pressed is one digit, however long it lasts.
Twist and level
Twist is the level of the high tone minus the level of the low tone. A phone sends both at about the same level, but a phone line, a cheap speaker or a mic can cut one of them. The Standard limit allows the high tone to be up to 4 dB louder and the low tone up to 8 dB louder, a common rule for telephone lines. Loose allows 12 dB either way. The level of each tone is shown in dBFS, where 0 is the loudest a recording can hold, so −10 dBFS is a healthy tone and −45 dBFS a faint one.
Use cases
Old answering machine tapes
A digitised cassette of an old answering machine often holds the beeps of someone checking messages from a remote phone, or the number a caller typed into a menu. Open the file and the digits appear with their times, so you can jump to 1:42 and hear the call where 0 was pressed. Tape hiss is no problem: tones at −30 dBFS over hiss at −50 dBFS decode cleanly.
Radio control tones
Ham radio repeaters and some remote sites are switched with short DTMF sequences sent over the air, and two-way radios can send an ID as tones at the start of each call. Point the mic at the radio's speaker, or record the audio output, and read the codes with their timing. Radio tones can be sent fast, sometimes 50 ms or less each, so keep the minimum tone length at 40 ms or lower it to 25 ms.
Testing a phone system
If a phone menu or an office phone system misses key presses, record what the phone sends and check the Digit list. Tones shorter than 40 ms, a twist of more than 4 to 8 dB, or a very low level are common reasons a system ignores a key. The CSV gives every value, so you can compare two phones side by side.
Tips for clean decoding
- Open the file when you have one. A recording opened here is cleaner than playing it into the mic, because room echo and noise never get in.
- Use a mid volume. The Low / high readout should show both tones between about −30 and −6 dBFS. Clipping (the red badge) adds extra tones that can block a key.
- Loose twist for mic recordings. Phone speakers are often weak in the low tones, so the low tone reads quieter. Loose twist lets those keys through.
- Raise the minimum tone length for doubled digits. A held key that fades or breaks up can read twice; 65 or 100 ms joins the parts.
Speech and music rarely hold two clean tones at DTMF frequencies for 40 ms, so they are ignored. Music played on pure, sine-like sounds can still trigger a rare false digit. For Morse beeps instead of keypad tones, use the Morse decoder, and to read the speed of an engine from its sound, see RPM from sound. All decoders are on the more signal decoders page.
FAQ
What is DTMF?
Dual-tone multi-frequency: each phone key plays two tones at once, one low and one high.
Why are some digits doubled?
A key held for long may read twice if it pauses. Raise the minimum tone length.
Can it decode tones from music or speech?
It uses strict rules to ignore them, but very tonal music can still trigger rare false digits.
Is it legal?
Decoding your own recordings is fine. Respect privacy and recording laws for calls.