Room acoustics · Guide
How to EQ a room with an RTA
Most rooms add more to the sound than the speakers do. One bass note booms, another nearly disappears, and the treble changes with every curtain and sofa. An RTA (real-time analyzer) and pink noise show you what your room does at the listening seat, so you can fix it with a few careful EQ cuts instead of guessing. This guide walks you through it in six steps, and tells you what EQ cannot fix.
This guide has links to products. We may earn a commission if you buy through these links. It does not change the price.
Try it
The RTA opens with 1/3-octave bands, slow averaging and the gentle house curve as the target. Press Pink noise to play the test sound through your speakers, then Listen to measure it with your mic.
What you need
You need four things: your speakers and the amp or receiver that drives them, an EQ you can adjust (the EQ menu of an AV receiver, a DSP or a plugin on your computer), a device that runs the RTA in a browser, and a microphone. A phone or laptop mic is fine for a first look at the mid range, but most of them roll off below about 50 Hz and many add their own coloration, which is exactly where room problems live. For bass work, a measurement mic with its own calibration file, such as the miniDSP UMIK-1, gives results you can trust. A mic stand or a tripod at ear height helps a lot.
We may earn a commission if you buy through these links. It does not change the price.
Steps 1–3: set up the measurement
Step 1: put the mic where you listen
Place the mic where your head goes when you listen: the main seat, at ear height, about 1 to 1.2 m from the floor for a sofa. Point it at the ceiling or at the speakers, as its calibration file says; measurement mics often come with one file for each. Keep it away from the back of the sofa and from your own body, because a nearby surface adds reflections that are not part of the room you hear. Close doors and windows, switch off fans and turn off any “loudness”, “bass boost” or automatic room correction on the receiver, so you measure the room and not a setting.
Step 2: set a steady level
Press Pink noise in the RTA. Pink noise has the same energy in every octave, so on a 1/3-octave RTA it shows as a flat line when the speakers and room are flat; every hill and valley you see comes from the system. Raise the volume until the noise is clearly louder than the room’s background, a moderately loud level like music played with friends, and keep it there for the whole session. Too quiet and noise from the street gets into the bass bands; too loud and the speakers start to strain. If the RTA shows a “Loud” badge, turn it down a little.
Step 3: average over time and positions
Pink noise is random, so a single moment jumps around by a few dB. Set averaging to Slow, or Infinite for a long average, and wait 10 to 20 seconds until the bars settle. Then move the mic: bass in a room changes a lot over half a metre, so one spot can show a dip that is gone at the next seat. Measure 5 to 9 spots around the main seat, within about a metre of it, and store each result with Store curve. What the curves share is the room; what changes from spot to spot is not worth correcting.
Steps 4–6: read, cut and check
Step 4: read the curve
Compare the averaged curve with the target. The RTA’s house curve falls about 1 dB per octave toward the treble, which most people find more natural in a room than a dead-flat line. Look at the bass first, below about 300 Hz, where the room’s own resonances, its room modes, decide the sound. A band that sits 6 dB or more above its neighbours in every stored curve is a peak worth fixing; at 63 Hz it is the note that booms on every bass line. Narrow dips that move between mic spots are cancellations. Above about 500 Hz the curve mostly shows the speakers themselves, so small wiggles there are rarely worth touching.
Step 5: cut the peaks
Use a parametric EQ band for each peak: set its frequency to the centre of the peak, cut by about the amount it stands above the target, and start with a fairly narrow width (a Q of 4 to 8 for a single bass mode). On a 31-band graphic EQ, pull down the slider at that band and maybe a little on the bands next to it. Make one change at a time and keep cuts below about 10 dB. A tall peak that needs more is a sign that the speaker or the seat is in a bad spot, and moving it will help more than EQ.
Step 6: measure again
Measure the same spots again with the EQ on and compare with the stored curves. The peak should now sit near the target in most spots. If one band went too low, ease the cut; if the boom moved to a neighbouring band, adjust the frequency. Then listen to music you know well. Trust your ears for the last decibel: the RTA tells you where the problems are, and the music tells you when it is right. For more detail in the bass than 1/3-octave bars show, use 1/6 octave in the RTA or a sweep test.
Cut peaks, don’t boost dips
A peak and a dip look like mirror images on the RTA, but they have different causes. A peak at a room mode is extra energy: the room stores sound at that frequency and keeps it ringing. Cutting it with EQ takes energy out and works at every seat that hears the boom. A dip is usually a cancellation: sound from the speaker meets its own reflection from a wall, half a wave late, and the two cancel at that spot. If you boost the dip, you boost the direct sound and the reflection together, so they still cancel. The dip stays, while the amp and the woofer work much harder, up to four times the power for a 6 dB boost, and the boosted band now booms at other seats.
So the rule is simple: cut freely, boost little or not at all, and never more than about 3 dB. Dips are better fixed by moving things. Move the mic, or your seat, 30 to 50 cm and watch whether the dip moves too. Moving the speaker or the subwoofer away from the wall, or to a different spot along it, changes which frequencies cancel. A second subwoofer in another part of the room can fill dips that no EQ can.
If you have a subwoofer, set it up before any EQ, because its position, level and phase change the whole bass curve. With the RTA running on pink noise, try the sub in two or three places along the front wall and keep the one with the smoothest bass. Set its level so the bands under the crossover (80 Hz is a common choice) line up with the bands above it. Then flip the sub’s phase switch between 0 and 180 degrees and keep the setting that gives more level around the crossover: the wrong one leaves a hole exactly where the sub and the speakers meet.
Fix the room before EQ
EQ changes the sound at the frequencies you choose, but it cannot shorten the time a room keeps ringing. When the reverb is long, voices smear and bass notes blur into each other, whatever the curve looks like. Measure the room’s reverb time first: a living room around 0.4 to 0.6 seconds and a small studio around 0.2 to 0.4 seconds are good goals.
Treatment works on time as well as level. Thick bass traps in the corners, where all room modes meet, soak up low-frequency energy and calm the modes that EQ only flattens. Absorbing panels at the first reflection points, the spots on the side walls and ceiling where you would see a speaker in a mirror from your seat, make the stereo image sharper and the treble cleaner. A rug, curtains, a bookcase and a soft sofa help too. After treatment, measure again: peaks are often smaller, dips shallower, and the EQ you need is gentler. To see in advance which bass notes your room size makes strong, work out its room modes.
Common mistakes
- Measuring one spot. A single position shows dips that exist only there. Average 5 to 9 spots.
- EQing everything flat. Chasing every wiggle above 500 Hz makes the sound worse, because those wiggles change with each head movement. Fix the bass; leave the treble to the speakers.
- Boosting the deep bass. Adding 6 dB at 30 Hz to a small speaker that cannot play 30 Hz only makes it distort. Check what the speaker is made for first.
- Leaving processing on. Loudness, bass boost and automatic room correction change the curve while you measure. Switch them off, then decide later if you want them.
- EQ before placement. Every time a speaker, the sub or the seat moves, the bass curve changes. Place things first, measure, and only then set the EQ.
- Too loud pink noise. It tires your ears and can strain the speakers. A moderately loud level is enough.
- Forgetting to listen. The measurement guides you, but the goal is music that sounds right. Finish with songs you know well.
For all the room tools in one place, see the room acoustics tools.
FAQ
Should I EQ my room flat?
Aim for a gentle downward slope toward the treble; dead flat often sounds thin.
Why not boost dips?
Dips come from cancellations. Boosting wastes power and the dip stays.
How many mic positions?
Average 5–9 spots around the listening seat for a steadier result.
Graphic EQ or parametric?
Parametric is better for narrow bass peaks; a 31-band graphic EQ is fine for broad tone.